自动上料搅拌车工作量大，用户只要具备一定的维修知识，对使用会有很大帮助。不过，机械漏油是很常见的问题，今天就教大家这些小技巧。
The workload of the automatic feeding mixer truck is large. As long as the user has certain maintenance knowledge, it will be very helpful to use it. However, mechanical oil leakage is a common problem. Today, I will teach you these tips.
过度使用和油封是正常磨损情况。方法：更换新油封即可。
Excessive use and oil seals are normal wear conditions. Solution: Replace the oil seal with a new one.
长时间不更换机油，滤芯质量不合格，机油太脏，加速油封磨损。方法：尽快更换液压油和滤芯。
If the engine oil is not replaced for a long time, the filter element is unqualified, the engine oil is too dirty, and the oil seal is accelerated to wear. Solution: Replace the hydraulic oil and filter element as soon as possible.
传动轴平衡失效，摆动大，造成主轴摆动油封偏磨。方法：及时纠正并更换转轴。液压油变质乳化，导致润滑性能下降，加速油封磨损。方法：尽快更换液压油和滤芯，严重时需要清洗系统。泵支架松动，开泵，泵固定螺栓松动，进而引起液压泵整体振动和油封磨损。
The balance of the transmission shaft fails and the swing is large, causing eccentric wear of the main shaft swing oil seal. Solution: Correct and replace the shaft in time. The hydraulic oil is deteriorated and emulsified, which leads to the decline of lubricating performance and accelerates the wear of oil seals. Solution: replace the hydraulic oil and filter element as soon as possible, and clean the system in serious cases. The pump bracket is loose, the pump is started, and the pump fixing bolts are loose, which causes the overall vibration of the hydraulic pump and the wear of the oil seal.
方法：经常检查和排除自动上料搅拌车可能出现的故障，防止和避免故障。
Solution: Frequently check and eliminate possible faults of automatic feeding mixer truck to prevent and avoid faults.
自动上料搅拌系统回油不畅，回油管和散热器堵塞，进而导致电机壳内压力升高，造成油封漏油。方法：堵塞物，保持回油循环通畅。如果散热器不散热，油温过高，粘度和润滑性下降，油封过热，密封失效。方法：对散热器进行故障排除，对系统进行冷却过程，避免泵电机磨损。严重时，停止发动机并熄火，用水冲洗泵电机和散热器外壳，以达到冷却效果。
The oil return of the automatic feeding and mixing system is not smooth, and the oil return pipe and radiator are blocked, which leads to the pressure rise in the motor housing and oil leakage of the oil seal. Solution: Remove the blockage and keep the oil return circulation smooth. If the radiator does not dissipate heat, the oil temperature is too high, the viscosity and lubricity are reduced, the oil seal is overheated, and the seal fails. Solution: Troubleshoot the radiator and cool the system to avoid wear of the pump motor. In serious cases, stop the engine and shut down, flush the pump motor and radiator housing with water to achieve cooling effect.
自动上料搅拌车
Automatic feeding mixer
以上就是为大家介绍的有关
全自动上料搅拌车的详细的介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务
The above is a detailed introduction to the fully automatic feeding mixer, and I hope it will be helpful to you. If you have any questions, please contact us. We will provide services for you with our attitude
山汽微信
2022-12-23
首页
产品
电话
置顶