全自动上料搅拌车偶尔会出现很多土渣未被清楚干净情况，因此在作业过程中才会出现很多事故，小编同学告诉大家5种方法可以轻松将自动上料搅拌车的渣土清理干净，快去看看吧！
Occasionally, there will be a lot of soil residue is not clear and clean in the full-automatic feeding mixer, so there will be a lot of accidents in the process of operation. I'd like to tell you that five methods can easily clean up the residue of the automatic feeding mixer. Go and have a look!
首先应准备好紧急驱动软管，将机械熄火，卸下液压马达上的高压油管接头。
First, prepare the emergency drive hose, turn off the machine, and remove the high-pressure oil pipe joint on the hydraulic motor.
将救援车熄火，将液压马达的高压油管拆卸，并与故障车上的相应接头利用紧急驱动软管相连接。
Shut down the rescue vehicle, dismantle the high-pressure oil pipe of the hydraulic motor, and connect it with the corresponding connector on the fault vehicle by using the emergency drive hose.
发动救援车并将操作手柄拨动至出料位置，故障车中的混合便会被排出。
Start the rescue vehicle and move the operating handle to the discharging position, and the mixture in the fault vehicle will be discharged.
当紧急驱动完成后，将自动上料搅拌车中的驱动软管拆卸，并回复至原状。
When the emergency drive is completed, remove the drive hose in the automatic feeding mixer and return to the original state.
在拖轮、滚道间放入木楔，并控制搅拌筒的旋转，将发动机熄火，将液压马达的一根高压油管拆卸，搅拌筒可自由旋转并控制搅拌筒的旋转。从而让维修孔转到下部位置，然后将维修孔打开，并清理出筒中的混凝土，当混凝土排出完成后，恢复自动上料搅拌车的原来状态即可。
Put a wooden wedge between the tugboat and the raceway, control the rotation of the mixing drum, turn off the engine, and dismantle a high-pressure oil pipe of the hydraulic motor. The mixing drum can rotate freely and control the rotation of the mixing drum. So that the maintenance hole is turned to the lower position, and then the maintenance hole is opened, and the concrete in the cylinder is cleaned out. When the concrete is discharged, the original state of the automatic feeding mixer can be restored.
以上5种方式均可将残留其中的土渣清除干净，不管您会现在哪种方法都要注意安全问题，想要了解更多内容欢迎点击我们的网站。
The above five methods can remove the residue, no matter which method you will now, you should pay attention to the safety issues. For more information, please click our Website. 全自动上料搅拌车偶尔会出现很多土渣未被清楚干净情况，因此在作业过程中才会出现很多事故，小编同学告诉大家5种方法可以轻松将自动上料搅拌车的渣土清理干净，快去看看吧！
Occasionally, there will be a lot of soil residue is not clear and clean in the full-automatic feeding mixer, so there will be a lot of accidents in the process of operation. I'd like to tell you that five methods can easily clean up the residue of the automatic feeding mixer. Go and have a look!
首先应准备好紧急驱动软管，将机械熄火，卸下液压马达上的高压油管接头。
First, prepare the emergency drive hose, turn off the machine, and remove the high-pressure oil pipe joint on the hydraulic motor.
将救援车熄火，将液压马达的高压油管拆卸，并与故障车上的相应接头利用紧急驱动软管相连接。
Shut down the rescue vehicle, dismantle the high-pressure oil pipe of the hydraulic motor, and connect it with the corresponding connector on the fault vehicle by using the emergency drive hose.
发动救援车并将操作手柄拨动至出料位置，故障车中的混合便会被排出。
Start the rescue vehicle and move the operating handle to the discharging position, and the mixture in the fault vehicle will be discharged.
当紧急驱动完成后，将自动上料搅拌车中的驱动软管拆卸，并回复至原状。
When the emergency drive is completed, remove the drive hose in the automatic feeding mixer and return to the original state.
在拖轮、滚道间放入木楔，并控制搅拌筒的旋转，将发动机熄火，将液压马达的一根高压油管拆卸，搅拌筒可自由旋转并控制搅拌筒的旋转。从而让维修孔转到下部位置，然后将维修孔打开，并清理出筒中的混凝土，当混凝土排出完成后，恢复自动上料搅拌车的原来状态即可。
Put a wooden wedge between the tugboat and the raceway, control the rotation of the mixing drum, turn off the engine, and dismantle a high-pressure oil pipe of the hydraulic motor. The mixing drum can rotate freely and control the rotation of the mixing drum. So that the maintenance hole is turned to the lower position, and then the maintenance hole is opened, and the concrete in the cylinder is cleaned out. When the concrete is discharged, the original state of the automatic feeding mixer can be restored.
以上5种方式均可将残留其中的土渣清除干净，不管您会现在哪种方法都要注意安全问题，想要了解更多内容欢迎点击我们
全自动上料搅拌车网站。
The above five methods can remove the residue, no matter which method you will now, you should pay attention to the safety issues. For more information, please click our Website.
山汽官方微信
2022-12-23
首页
产品
电话
置顶