启动搅拌车自动上料的和液压系统，以便将在泵上获得的动量用于为液压马达提供动力。准备几乎自动启动排水泵，切换到清洁状态并控制操作按钮。排空水箱中的水，打开水箱底部的排水球阀，然后等待水箱中的水流出。按下排水系统按钮，观察泵出口的状况。当供水停止从泵出口流出时，操作完成，泵中的水完全排出。
Start the automatic feeding and hydraulic system of the mixer so that the momentum obtained on the pump can be used to provide power for the hydraulic motor. Prepare to start the drainage pump almost automatically, switch to clean state and control the operation button. Drain the water in the water tank, open the drain ball valve at the bottom of the water tank, and then wait for the water in the water tank to flow out. Press the drain system button to observe the condition of the pump outlet. When the water supply stops flowing out from the pump outlet, the operation is completed and the water in the pump is completely discharged.
根据以上过程，搅拌车自动上料的泵干净地排出，冬天不怕泵开裂。请注意，每次使用泵时，都必须将其排干。否则，它将在一夜之间被完全破坏，将无法使用。另外，在搅拌车自动上料的强制排水过程中，必须注意泵的出口。
According to the above process, the automatic feeding pump of the mixer is discharged cleanly, and the pump is not afraid of cracking in winter. Please note that the pump must be drained every time it is used. Otherwise, it will be completely destroyed overnight and will be unusable. In addition, attention must be paid to the outlet of the pump in the forced drainage process of automatic feeding of the mixer.
搅拌车自动上料的保养
Maintenance of automatic feeding of mixer truck
对于搅拌车自动上料的设备，发动机的使用非常重要，因此在正常设备制造过程中必须维护发动机。这是一些正确的发动机维护方法。
For the automatic feeding equipment of mixer, the use of engine is very important, so the engine must be maintained in the normal equipment manufacturing process. These are some of the right ways to maintain the engine.
1.首先，搅拌车自动上料的设备用塑料膜覆盖，然后在膜的上侧用半湿毛巾覆盖，以防止高压水涌入分配器，从而使搅拌车自动上料的难以启动。
1. First, the automatic feeding equipment of the mixer is covered with plastic film, and then the upper side of the film is covered with semi wet towel to prevent high-pressure water from flowing into the distributor, which makes it difficult to start the automatic feeding of the mixer.
2.用高压水枪从搅拌车自动上料的顶部到底部清除附着在发动机侧和发动机侧的污垢。
2. Use a high-pressure water gun to remove the dirt attached to the engine side and engine side from the top to the bottom of the mixer.
3.浸湿后，将搅拌车自动上料的外部清洁剂直接喷到搅拌机的发动机和机舱中。
3. After soaking, spray the external cleaning agent automatically fed by the mixer directly into the engine and engine room of the mixer.
4.闪烁3分钟后，使用纤维刷清洁机房中所有可接触的部件。
4. After flashing for 3 minutes, use the fiber brush to clean all accessible parts in the machine room.
5.用高压水枪快速冲洗被擦洗的污垢。
5. Use a high-pressure water gun to quickly wash the scrubbed dirt.
6.然后在发动机表面喷涂搅拌车自动上料的发动机外部清洁剂，操作步骤与上述相同。重复进行直至搅拌车自动上料的表面被清洁。
6. Then spray the engine external cleaning agent automatically fed by mixer truck on the engine surface, and the operation steps are the same as above. Repeat until the automatic feeding surface of the mixer is cleaned.
本文由
新2最新管理手机网址整理发布，您是不是对这些内容有所了解了呢?更多的内容请点击：
我们会有更多精彩内容等你查看。
This article is organized and released by the automatic feeding mixer. Do you know something about these contents? For more information, please click: We'll have a lot more to see.
山汽官方微信
2022-12-23
首页
产品
电话
置顶