新2手机会员端网址(中国)责任有限公司

常见问题

热点推荐

自动上料搅拌机配件是由哪两部分组成的？

2022-12-23

修路有哪些不错的机械设备？先说说这个小型搅拌车

2022-12-19

自上料搅拌车操作须知的五项重要内容

2022-12-16

自上料拌和车的特征有哪些？

2022-12-12

自动上料搅拌车能解决哪些施工难题？

2022-12-02

混凝土搅拌车的刹车片要怎样挑选合格

2022-11-14

关于山汽

联系人：刘老师

电话：400-879-1999

公司：新2手机会员端网址

地址：山东省莱州市206国道与308省道交叉口东南50米

混凝土搅拌机出现抱轴的原因是什么？

所属分类：常见问题发布时间：2022-04-09 来源：浏览量：0

混凝土搅拌机是生产混凝土的主要设备，混凝土搅拌机是把水泥、砂石骨料和水混合并拌制成混凝土混合料的机械。在使用过程中要注意日常保养，如果不注意保养，可能会出现抱轴的情况，混凝土搅拌机出现抱轴的原因也是有多种的。

Concrete mixer is the main equipment for producing concrete. Concrete mixer is a machine that mixes cement, gravel aggregate and water into concrete mixture. Pay attention to daily maintenance during use. If you don't pay attention to maintenance, axle holding may occur. There are many reasons for axle holding of concrete mixer.

1、混凝土搅拌机，可能是原料投料位置问题。搅拌混凝土所用的物料主要是砂石骨料、水泥、粉煤灰、水喝外加剂等。原料水泥若包裹砂石遇水结块，如果搅拌不充分就容易粘在搅拌轴上，若水泥进料口位置方向不合理，使搅拌轴不能快速充分搅拌，就容易形成抱轴现象。

1. The concrete mixer may be due to the feeding position of raw materials. The materials used for mixing concrete are mainly sand and gravel aggregate, cement, fly ash, water and drinking admixture, etc. If the raw cement is wrapped with sand and stone and agglomerates with water, it is easy to stick to the mixing shaft if it is not fully stirred. If the position and direction of the cement feed inlet is unreasonable, the mixing shaft cannot be quickly and fully stirred, and it is easy to form the phenomenon of shaft holding.

2、混凝土搅拌机进水管与冲水位置原因。冲水点位置和冲洗方向不正确的话，又或者是冲水压力过低，导致水在进入主机内部后，不能将暂时粘结在轴上的混凝土冲洗掉，则时间久了就容易形成抱轴。

2. Reasons for water inlet pipe and flushing position of concrete mixer. If the position and direction of the flushing point are incorrect, or the flushing pressure is too low, so that the water cannot flush the concrete temporarily bonded to the shaft after entering the main engine, it is easy to form the shaft holding after a long time.

3、混凝土搅拌机，在结构生产之后没有及时对混凝土搅拌机内部进行清洗，或清洗的不干净，导致搅拌轴表面仍有残留的混凝土，干燥后凝固在搅拌轴上，如果长期如此则非常容易产生抱轴现象。

3. For the concrete mixer, the interior of the concrete mixer is not cleaned in time after the structural production, or the cleaning is not clean, resulting in the residual concrete on the surface of the mixing shaft, which is solidified on the mixing shaft after drying. If this is the case for a long time, it is very easy to produce the phenomenon of shaft holding.

以上就是为大家介绍的有自动搅拌一体机的详细介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务http://www.shanqijituan.cn/

The above is a detailed introduction of the automatic mixing machine. I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service http://www.shanqijituan.cn/

上一页：混凝土自上料搅拌车的这些转速问题！下一页：自动搅拌车液压油更换有没有更便捷的方法