新2手机会员端网址(中国)责任有限公司

新2手机会员端网址
热线电话:400-879-1999 山汽官方微信
郑重声明 购机 售后
在线询价
热线电话:400-879-1999
您现在所在的位置: 首页> 新闻资讯 > 公司新闻

如何让混凝土搅拌机延长使用时间?

所属分类:公司新闻 发布时间:2020-07-07 来源: 浏览量:0

  有些用户会见到有些操作混凝土搅拌机的工作人员会在混凝土搅拌机传动齿轮每天开机前应涂抹黄油少许.并在链条上加涂少量的润滑脂,每工作300小时清洗链条一次,每星期打开一次各传动链条罩壳。混凝土搅拌机每班工作结束后将混合料存仓中的物料排放干净,切断总电源,检查搅拌臂与叶浆的紧固情况,发现螺母松动应立即拧紧,这些都是日常所需要注意的。混凝土搅拌机的使用寿命与日常保养有相当大的关系,新2最新管理手机网址维修和保养应注意以下几点:
  Some users will see that some workers who operate the concrete mixer will apply a little butter before starting the concrete mixer drive gear every day, and apply a small amount of grease on the chain, clean the chain once every 300 hours, and open the cover of each drive chain once a week. After the end of each shift of the concrete mixer, the materials in the storage bin of the mixture shall be discharged, the main power supply shall be cut off, and the fastening condition between the mixing arm and the blade slurry shall be checked. If the nut is loose, it shall be tightened immediately. These are the daily needs. The service life of concrete mixer is closely related to daily maintenance. The following points should be paid attention to in the maintenance and repair of full-automatic feeding mixer:
  (1)各部分紧固螺栓经常检查,特别是搅拌机座、电机座、叶片与衬板,以防松脱。
  (1) Check the fastening bolts of all parts, especially the mixer base, motor base, blade and lining plate, to prevent loosening.
  (2)更换混凝土搅拌机叶片时应用标准扭力扳手,锁紧力矩应达200-220N.m。
  (2) When replacing the blade of concrete mixer, the standard torque wrench should be used, and the locking torque should be 200-220n. M.
              新2最新管理手机网址
  (3)混凝土搅拌机搅拌叶片与衬板之间磨损间隙过大时,筒体水平两侧应调至≤5mm。
  (3) When the wear clearance between the mixing blade and the lining plate of the concrete mixer is too large, the horizontal sides of the cylinder should be adjusted to ≤ 5mm.
  (4)减速机润滑油要按标准定期更换。
  (4) The lubricating oil of reducer shall be changed regularly according to the standard.
  (5)检查混凝土搅拌机润滑泵是否按程序设置正常工作。
  (5) Check whether the lubrication pump of concrete mixer works normally according to the program setting.
  (6)每班次或停机前要清洗搅拌桶、轴、叶片。
  (6) Clean the mixing drum, shaft and blade before each shift or shutdown.
  (7)同步齿轮、传动链条要定期清理,加润滑油脂。
  (7) The synchronous gear and transmission chain should be cleaned regularly and lubricated.
  (8)冰冻季节,应将喷水系统内存水放净。
  (8) In the freezing season, the water in the sprinkler system should be drained.
  以上是关于新2最新管理手机网址的维修保养注意事项的详细介绍,想要了解更多内容欢迎咨询官网。
  The above is a detailed introduction to the maintenance precautions of automatic feeding mixer. If you want to know more, please consult Official website.

 

首页 产品 电话 置顶
Baidu
sogou