正确操作全自动小型上料搅拌车的注意事项，生产的全自动小型上料搅拌车的液压系统压力应符合使用说明书中的规定，不得随意调整。液压油的油质和油量应符合原定要求。全自动小型上料搅拌车装料前，应先排净拌筒内残存的积水和杂物。在运输过程中要不停的转动，以防混凝土离析。全自动小型上料搅拌车到达工地和卸料之前，应先使拌筒全速以14-18转/分转动1-2分钟，然后再进行反转卸料。反转之前，应使搅拌筒停稳不转。
The hydraulic system pressure of the full-automatic small loading mixer should be in accordance with the provisions in the operation manual, and should not be adjusted at will. The quality and quantity of hydraulic oil should meet the original requirements. Before loading, the residual water and debris in the mixing drum should be drained. In the process of transportation, keep rotating to prevent concrete segregation. Before the full-automatic small loading mixer arrives at the construction site and unloads, the mixing drum should be rotated at full speed at 14-18 rpm for 1-2 minutes, and then reverse the unloading. Before reversing, the mixing drum should be stopped stably.
全自动小型上料搅拌车罐内温度高于25摄氏度，从装料，运输，到卸料延续时间不得超过60分钟，环境温度低于25摄氏度，上述时间不得超过90分钟。冬期施工时应切实做到：开机前检查是否结冰;下班时认真排除拌筒内及供水系统内残存积水，关闭水泵开关，将控制手柄置于“停止”位置。
When the temperature in the tank of the full-automatic small loading mixer is higher than 25 ℃, the duration from loading, transportation to unloading shall not exceed 60 minutes, and the above time shall not exceed 90 minutes when the ambient temperature is lower than 25 ℃. During winter construction, it is necessary to check whether there is icing before starting the machine; when off duty, carefully remove the residual water in the mixing drum and water supply system, turn off the water pump switch, and put the control handle at the "stop" position.
搅拌车在施工现场卸料完毕后，应立即用搅拌车随带的软管冲洗进料斗，出料斗，卸料溜槽等处，粘附在车身各处的污泥及混凝土。在返回搅拌站的途中，应向搅拌筒内注150 --- 200L水以清洗筒壁及叶片粘结的混凝土残渣。
After the mixer truck is unloaded at the construction site, the inlet hopper, discharge hopper, discharge chute and other places shall be washed with the hose attached to the mixer to remove the sludge and concrete adhered to the vehicle body. On the way back to the mixing station, 150-200l water should be injected into the mixing drum to clean the concrete residue bonded by the cylinder wall and blades.
全自动小型上料搅拌车在工作时，不得将手伸入旋转的搅拌筒内，严禁将手伸入主卸料溜槽和加长卸料溜槽的连接部位，以免发生事故。应定期检查搅拌叶片磨损情况并及时进行修补和换新。各项有关操作规范。混凝土搅拌运输车司机须经过培训，无合格证者不得上岗操作。
When the full-automatic small loading mixer is working, it is not allowed to put hands into the rotating mixing drum, and it is strictly prohibited to put hands into the connection part of the main discharge chute and the extended discharge chute, so as to avoid accidents. The abrasion of mixing blades should be checked regularly and repaired and replaced in time. All relevant safety operation specifications. The driver of concrete mixer truck must be trained professionally, and the operator without certificate is not allowed to work.
全自动小型上料搅拌车常见维护问题，全自动小型上料搅拌车厂家告诉您使用小型搅拌罐车的时候出现罐体问题的，是如何造成如何呢，今在“钱”进的路上没有障碍，我们时刻为你为您着想，全自动小型上料搅拌车出现罐体质量问题，只能眼睁睁的看着混凝土凝固，郑州漫星专在这个点提出方案，有了它再也不用担心混凝土凝固的问题了。
Full automatic small loading mixer common maintenance problems, automatic small mixing truck manufacturers tell you the use of small mixing tank truck tank problems, how to solve? Today, Zhengzhou manxing in order to everyone in the "money" on the road, we always think for you, full-automatic small feeding mixer tank body quality problems, only To be able to watch the concrete solidification, Zhengzhou manxing puts forward a solution at this point. With it, there is no need to worry about the problem of concrete solidification.
导致全自动小型上料搅拌车的主要原因：
The main reasons for the automatic small loading mixer are as follows:
1.全自动小型上料搅拌车发动机故障：发动机无法启动，取力器损坏等原因。
1. Engine failure of full-automatic small loading mixer: the engine cannot be started and the power take-off is damaged.
2.上装罐的故障：传动轴损坏，油泵故障，液压油过脏或油量不足，马达故障，减速机故障，操纵杆松脱等原因。
2. Faults of top loading tank: damaged transmission shaft, oil pump failure, dirty or insufficient hydraulic oil, motor failure, reducer failure, loose control rod, etc.
山汽微信
2022-12-23
首页
产品
电话
置顶